Trying

Submitted by Octane on
Forum
Work in progress

I'm trying to get my mesh flow better is there anything i've done wrong?[?]

[img]icon_paperclip.gif[/img] Download Attachment: [url="http://www.sumea.com.au/forum/attached/Octane/20052583855_front.jpg"]front.jpg[/url]
20.8 KB

[img]icon_paperclip.gif[/img] Download Attachment: [url="http://www.sumea.com.au/forum/attached/Octane/2005258395_persp.jpg"]persp.jpg[/url]
21.73 KB

Submitted by Kalescent on Sun, 06/02/05 - 12:50 PM Permalink

Hey Octane - What kind of a polycount you going for ? Unless your trying to keep it down quite low maybe under 1200-1500 Tri's then I would avoid the 7 edges leading to that single point at the front of his armpit there. Instead get some good lines flowing around the shoulder like this : ( btw this is only how I would approach it - so purely personal preference )

[img]http://www.sumea.com.au/forum/attached/Hazard/2005259497_FrontHelp.jpg[…]

Shortcut Key for Remove edge is Backspace in case you didnt know - so just select edge and backspace.

Hopefully that helps a bit [:)]

Submitted by Octane on Sun, 06/02/05 - 1:03 PM Permalink

Thanks Hazard, you should seen the arm pit ealier lol it was a mess.
i have no polycount just trying to get better and yeah i kinda sat down and learned the short cuts to try and move a bit faster ;) but yeah i was hopeing someone would draw where to put the lines it's very helpful.

Submitted by Octane on Tue, 08/02/05 - 6:32 AM Permalink

a few more pics

[img]icon_paperclip.gif[/img] Download Attachment: [url="http://www.sumea.com.au/forum/attached/Octane/20052733220_front1.jpg"]front1.jpg[/url]
31.67?KB

[img]icon_paperclip.gif[/img] Download Attachment: [url="http://www.sumea.com.au/forum/attached/Octane/20052733232_back1.jpg"]back1.jpg[/url]
35.46?KB

heres the ref image
[img]icon_paperclip.gif[/img] Download Attachment: [url="http://www.sumea.com.au/forum/attached/Octane/20052735917_ref.jpg"]ref.jpg[/url]
85.88 KB

Posted by Octane on
Forum
Work in progress

I'm trying to get my mesh flow better is there anything i've done wrong?[?]

[img]icon_paperclip.gif[/img] Download Attachment: [url="http://www.sumea.com.au/forum/attached/Octane/20052583855_front.jpg"]front.jpg[/url]
20.8 KB

[img]icon_paperclip.gif[/img] Download Attachment: [url="http://www.sumea.com.au/forum/attached/Octane/2005258395_persp.jpg"]persp.jpg[/url]
21.73 KB

Submitted by Kalescent on Sun, 06/02/05 - 12:50 PM Permalink

Hey Octane - What kind of a polycount you going for ? Unless your trying to keep it down quite low maybe under 1200-1500 Tri's then I would avoid the 7 edges leading to that single point at the front of his armpit there. Instead get some good lines flowing around the shoulder like this : ( btw this is only how I would approach it - so purely personal preference )

[img]http://www.sumea.com.au/forum/attached/Hazard/2005259497_FrontHelp.jpg[…]

Shortcut Key for Remove edge is Backspace in case you didnt know - so just select edge and backspace.

Hopefully that helps a bit [:)]

Submitted by Octane on Sun, 06/02/05 - 1:03 PM Permalink

Thanks Hazard, you should seen the arm pit ealier lol it was a mess.
i have no polycount just trying to get better and yeah i kinda sat down and learned the short cuts to try and move a bit faster ;) but yeah i was hopeing someone would draw where to put the lines it's very helpful.

Submitted by Octane on Tue, 08/02/05 - 6:32 AM Permalink

a few more pics

[img]icon_paperclip.gif[/img] Download Attachment: [url="http://www.sumea.com.au/forum/attached/Octane/20052733220_front1.jpg"]front1.jpg[/url]
31.67?KB

[img]icon_paperclip.gif[/img] Download Attachment: [url="http://www.sumea.com.au/forum/attached/Octane/20052733232_back1.jpg"]back1.jpg[/url]
35.46?KB

heres the ref image
[img]icon_paperclip.gif[/img] Download Attachment: [url="http://www.sumea.com.au/forum/attached/Octane/20052735917_ref.jpg"]ref.jpg[/url]
85.88 KB